Nuevo servoaccionamiento original AS3-04BAI yako AC

86mm Series 2 Phase Open-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK86HB65-04A     1.8 65 3.2 4.0 0.65 3.9 1000 1.7 8 YK86HB80-04A 1.8 80 4.5 6.0 0.4 3.5 1400 2.3 8 YK86HB118-06A 1.8 118 8.5 6.0 0.6 6.5 2700 3.8 8 YK86HB156-06A 1.8 156 12.0 6.2 0.7 9.0 4000 5.3 8 Dimensions Dimensions Model  Shaft Diameter D(mm)  Shaft Type (mm) Shaft Length L1 (mm)    YK86HB65-04A  9.5 Flat 1*25 32 YK86HB80-04A  12.7 Flat 1*25 32 YK86HB118-06A  12.7 Key 5*5*25 32 YK86HB156-06A  15.875 Key 5*5*25 32 Motor connection

el variador paso a paso de CA se alimenta de 24 a 50 V y está diseñado para usarse con motores paso a paso diseñados para manejar un alto voltaje de bus de 340 VCC.

YKA2811MA variador paso a paso de bucle abierto, rango de corriente de variador ajustable de 0.5a/fase - 8a/fase; protección de sobretensión, sobrecalentamiento y sobrecorriente.

YKE2608MH-IO Spontaneous Impulse Stepper Drive  YKE2608MH-IO is a high-performance stepper driver based on a new generation of digital control technology. The control mode of the driver is spontaneous pulse speed control. There are 16 segments of speed can be set by 4 DIP switches, and any speed within the range can be set through the upper computer. Three-way photoelectric isolation digital input, the driver supports motor parameter identification and phase memory functions; Its similar servo control principle, unique circuit design, superior software algorithm processing can make the motor running stably at low speed, and accurate current control technology greatly reduces the motor fever.  Performance:  32-bit DSP control, low noise and superior vibration performance Three-way optocoupler isolated digital signal input, compatible with 5V/24V signals, support common cathode and anode connection mode Using the latest resonance suppression algorithm, it has excellent stationarity at medium and low speed With 8 current, 16 speed optional Running current, speed, acceleration and deceleration can be set in the upper computer debugging software The lock current can be set by the upper computer, the default setting current is 50% Small size, volume 151*94*54 (mm³), weight 0.5kg  Application:  YKE2608MH-IO is mainly used for speed controling, loading machine, unloading machine, docking station, logistics transmission, load shifting equipment, electronic equipment Dimensions: YKE2608MH-IO Roted Speed Setting: The / speed 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RPM 50 150 250 350 450 550 650 750 850 950 5 10 20 30 40 100 SW8 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF SW7 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF SW6 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF SW5 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW4=OFF Control Mode 2 lN1 lN2 statue invalid invalid locking valid invalid CW invalid valid locking valid valid BW SW4=ON Control Mode 1 lN1 lN2 statue invalid invalid locking valid invalid CW invalid valid BW valid valid locking YKE2608MH-IO Current Setting: RMS Default(2.00) 2.57 3.14 3.71 4.28 4.86 5.43 6.00 Peak Default(2.40) 3.08 3.77 4.45 5.14 5.83 6.52 7.20 SW3 ON ON ON ON OFF OFF OFF OFF SW2 ON ON OFF OFF ON ON OFF OFF SW1 ON OFF ON OFF ON OFF ON OFF Terminal Introduction: Symbol Function Specification PWR Power indicator When power on, the green indicator lights up.  TM Work indicator Pulse signal indicator, when there is continuous pulse input, the green indicator light flashes, otherwise the green indicator light is always on. O.C Fault indicator When over current or under voltage, the red indicator lights up. ln1+ input signal 1 electro-optical isolation + Connect signal power, for +5~+24V, when over +24V the ln1- need to connect current-limiting resistance. ln1- input signal 1 electro-optical isolation - It requires: low level 0~0.5V, high level 5~24V. ln2+ input signal 2 electro-optical isolation + Connect signal power, for +5~+24V, when over +24V the ln2- need to connect current-limiting resistance. ln2- input signal 2 electro-optical isolation - It requires: low level 0~0.5V, high level 5~24V. MF+ Motor free signal + Connect signal power, for +5~+24V, when over +24V the MF- need to connect current-limiting resistance. MF- Input signal - When it's in low level, cut off the motor current, and the drive stops working -V Power supply- AC18~80/DC30~110V +V Power supply + +A,-A   Motor connection +B,-B

la configuración automática del controlador paso a paso mide los parámetros del motor y configura el control de corriente del motor y los ajustes de ganancia antirresonancia. el controlador de alto voltaje usa una entrada de CA de 90 a 240 VCA y la corriente de salida se puede seleccionar de 0.6 a 2.5 a/fase (pico de seno).

YKE2608MH función de controlador paso a paso de bucle abierto para control DSP de 32 bits, bajo nivel de ruido y rendimiento de vibración superior, con sobretensión, bajo voltaje, etc.. protección contra fallas.

YKD3505M es un controlador paso a paso digital de alto rendimiento basado en la nueva tecnología DSP de 32 bits de YAKO's.